Docker Bridge на Ubuntu 14.04

Может есть вариант и попроще.


$ sudo service docker.io status
docker.io start/running, process 6536

$ ifconfig
docker0   Link encap:Ethernet  HWaddr aa:f0:35:9b:72:10  
          inet addr:172.17.42.1  Bcast:0.0.0.0  Mask:255.255.0.0
          inet6 addr: fe80::507e:2fff:fea1:6ae0/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:18 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:1224 (1.2 KB)  TX bytes:648 (648.0 B)

eth0      Link encap:Ethernet  HWaddr bc:ae:c5:30:13:a5  
          inet addr:192.168.1.5  Bcast:192.168.1.255  Mask:255.255.255.0
          inet6 addr: fe80::beae:c5ff:fe30:13a5/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:60789443 errors:0 dropped:73 overruns:0 frame:0
          TX packets:72579419 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:47728813127 (47.7 GB)  TX bytes:81564408216 (81.5 GB)

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:65536  Metric:1
          RX packets:258380 errors:0 dropped:0 overruns:0 frame:0
          TX packets:258380 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:311261549 (311.2 MB)  TX bytes:311261549 (311.2 MB)

veth5f79  Link encap:Ethernet  HWaddr aa:f0:35:9b:72:10  
          inet6 addr: fe80::a8f0:35ff:fe9b:7210/64 Scope:Link
          UP BROADCAST RUNNING  MTU:1500  Metric:1
          RX packets:9 errors:0 dropped:0 overruns:0 frame:0
          TX packets:8 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:738 (738.0 B)  TX bytes:648 (648.0 B)



$ sudo apt-get install bridge-utils

-- без lxc возникала ошибка при вызове контейнера с параметрами:

Error: Cannot start container 15251ef28c49d0cffeedcec5f90677c58cd2a4fba385f9335414eeb56deab440: lxc.network.ipv4 = 192.168.1.25/24 is not supported by the native driver

$ sudo apt-get install lxc


-- Нахер удаляю Network Manager и resolvconf
$ sudo apt-get remove network-manager
$ sudo apt-get remove resolvconf



$ sudo vi /etc/network/interfaces

auto lo
iface lo inet loopback


auto br0
iface br0 inet static
        address 192.168.1.5
        netmask 255.255.255.0
        gateway 192.168.1.1
        bridge_ports eth0
        bridge_stp off
        bridge_maxwait 0
        post-up /sbin/brctl setfd br0 0


$ sudo vi /etc/resolv.conf
nameserver 192.168.1.1


$ sudo reboot

============================



-- Нахер вырубаю докер с его виртуальным адаптером

$ sudo service docker.io stop
$ sudo ip link set dev docker0 down
$ sudo brctl delbr docker0


$ sudo vi /etc/default/docker.io
DOCKER_OPTS="-b=br0 -d -e lxc"
$ sudo service docker.io restart


~$ brctl show
bridge name	bridge id		STP enabled	interfaces
br0		8000.bcaec53013a5	no		eth0
							veth9fe6


$ sudo docker  run -i -t \
--lxc-conf="lxc.network.ipv4 = 192.168.1.11/24" \
centos:centos6 /bin/bash




Почитать:
http://askubuntu.com/questions/452611/how-to-use-docker-io-containers-in-ubuntu-14-04-with-ipv6